How To Change Blades On Gravely Zero Turn Mower?

Change blades on your Gravely zero turn mower is a simple procedure that can be performed by anyone. You won’t need to hire a professional, just follow the steps in this article and you’ll be done within 30 minutes.

If you own a Gravely zero turn mower, chances are you will need to change the blades at some point. Here are some tips on how to change the blades on your Gravely zero turn mower. First, you will need to remove the old blades.

To do this, you will need to disconnect the blade spindle assembly from the mower deck. Next, you will need to remove the bolts that hold the blades in place. Finally, you will need to remove the old blades and discard them.

How To Change Blades On Gravely Zero Turn Mower

  • Park your Gravely zero turn mower on a level surface
  • disengage the blades by pulling the PTO switch to the “OFF” position
  • Raise the deck of the mower to its highest position
  • Remove the bolts that hold the current blades in place
  • Install the new blades and tighten the bolts
  • Lower the deck of the mower back to its original position
  • engage the blades by pulling the PTO switch to the “ON” position

How to lower blades on gravely zero turn mower?

Blade lowering is a simple process that can be accomplished with a screwdriver and some patience. The first step is to remove the blade guard by gently prying it off with a flat-head screwdriver. Once the guard is removed, you will see two hex nuts holding the blade down at each end. Remove these nuts and remove the blade completely from the mower frame.

Turn your mower upside down so that you can access the underside of your mower where the blades are located. You will see two separate blades for each wheel on your mower. Each wheel has two blades that are about 1/4-inch wide. You will need to loosen these bolts slightly and then lower them down into place until they just touch each other.


To adjust the blade height, you need to first locate the adjustment knob. The knob is usually located near the front of the mower. Once you have found the knob, you need to rotate it to the desired position.

The position of the knob will determine how low the blades will be. Once you have the blades in the desired position, you can begin mowing. The Gravely zero turn mower is a great mower and will provide you with a great looking lawn.

Are gravely blades reverse threaded?

yes, gravely blades are reverse threaded. This is so that when you’re changing the blade, the new blade will be tight and secure. It’s important to follow the manufacturer’s instructions when changing the blade, and to use the proper tools.

If you’re a lawn care professional, you know that maintaining your equipment is key to providing quality services. Part of that maintenance is keeping your blades sharp and in good condition. But have you ever wondered if gravely blades are reverse threaded?

If you’re not a lawn care professional, you may be wondering why this information is important. After all, you probably don’t have to worry about changing the blade on your gravely mower. But if you’re ever in a situation where you need to change the blade, knowing that it’s reverse threaded will save you a lot of time and frustration.

So the next time you’re at the hardware store, take a look at the blades and see for yourself.

Gravely blade bolt size

Gravely blades are made to fit a variety of different lawn mowers, so the size of the bolt that holds the blade in place can vary. The most common sizes are 5/8″, 3/4″, and 1″, but some models may use a different size. To be sure you get the right size bolt for your Gravely blade, check the owner’s manual for your mower model.

How do you take the blades off a Gravely zero turn?

If you need to remove the blades from your Gravely zero turn mower, the process is actually quite simple. First, you’ll need to locate the blade bolts. There are typically two bolts per blade, and they will be located near the center of the blade.

Using a socket wrench, loosen the bolts until they are no longer tight. Next, you’ll need to remove the nuts that secure the blades to the spindle. Again, there are typically two nuts per blade.

Finally, you can remove the blades from the mower.

How do I change the blade on the zero turn mower without removing the deck?

There are a few different ways that you can change the blade on your zero turn mower without removing the deck. One way is to use a zero turn mower blade kit. This kit will come with everything you need to change the blade, including a new blade, a blade adapter, and a blade wrench.

Another way to change the blade is to use a lawn mower blade sharpener. This sharpener will allow you to sharpen the blade without removing the deck.

How do you jack up a zero turn mower?

If you need to jack up your zero turn mower, there are a few things you need to do first. Make sure that the area around the mower is clear and free of any obstacles. Next, locate the jack points on the mower.

These are typically located on the underside of the mower deck near the front or rear wheels. Once you have located the jack points, place the jack under the mower deck and raise it up until the wheels are off the ground. If you are jacking up the mower to perform maintenance or repairs, make sure to follow all safety precautions.

Always support the mower deck with jack stands before working on it, and never work on the mower while it is jacked up. When you are finished, lower the mower deck back down and remove the jack stands before operating the mower.

Which way do I turn the bolt to remove mower blades?

If you’re unsure about which way to turn the bolt to remove mower blades, there are a few things you can do to figure it out. First, try to identify which way the blade is currently turning. If it’s clockwise, then you’ll want to turn the bolt counterclockwise to loosen it.

If the blade is turning counterclockwise, then you’ll want to turn the bolt clockwise to loosen it. Another way to determine which way to turn the bolt is to look at the teeth on the blade. If the teeth are pointing up, then you’ll want to turn the bolt clockwise to loosen it.

If the teeth are pointing down, then you’ll want to turn the bolt counterclockwise to loosen it. Once you’ve determined which way to turn the bolt, use a wrench or socket to loosen it. Be sure to hold onto the blade with your other hand so it doesn’t come flying off when you loosen the bolt.

Once the bolt is loosened, you can remove the blade and put on a new one.

HOW TO EASILY CHANGE THE BLADES ON A GRAVELY RIDING MOWER!

Zero turn mower ramps for changing blades

If you own a zero turn mower, then you know that one of the most important maintenance tasks is to regularly change the blades. Not only do dull blades make it difficult to cut grass, but they can also damage your mower. That’s why it’s important to have a good set of ramps on hand to make changing the blades a breeze.

There are a few different types of ramps available on the market, but we think the best kind are the zero turn mower ramps. These ramps are specifically designed to fit most zero turn mowers, and they make it easy to get your mower up on the ramps so you can change the blades. To use the ramps, simply drive your mower up onto them and then use the included straps to secure the mower in place.

Once the mower is secured, you can safely change the blades. When you’re finished, simply drive the mower off of the ramps and you’re good to go. If you’re looking for a good set of ramps to help you change the blades on your zero turn mower, we highly recommend the zero turn mower ramps.

They’re easy to use and they’ll make the job a whole lot easier.

Conclusion

I have a Gravely ZTR mower and I don’t know how to lower the blades. I have been trying to lower the blades but they just keep on spinning….I’ve tried putting it in reverse and going forward, but that doesn’t work either!

Leave a Reply

Your email address will not be published. Required fields are marked *

Back To Top